Computer-aided Design And Computer-aided Manufacturing Research Articles

Contemporary Surgical Management of Craniofacial Fibrous Dysplasia Using Computer-Assisted Surgery and Intraoperative Navigation.

Craniofacial fibrous dysplasia (CFD) is a rare developmental disease of bone, which typically presents as a painless, expansile mass causing deformity of the craniofacial skeleton. In rare circumstances, compression of neurovascular structures may arise, causing symptoms such as pain, visual impairment, and hearing loss. Traditionally, CFD debulking has been performed with "freehand" techniques using preoperative imaging and anthropometric norms to determine the ideal amount of tissue removal. The advent of computer-assisted surgery, computer-aided design, and computer-aided manufacturing (CAD/CAM) has revolutionized the management of CFD. Surgeons can now fabricate patient-specific osteotomy/ostectomy guides, allowing for increased accuracy in bone removal and improved cosmetic outcomes. This series of 3 cases describe our institution's technique using patient-specific ostectomy "depth guides", which allow for maximum removal of fibro-osseous tissue while sparing deep and adjacent critical structures. These techniques can be widely applied to the craniofacial skeleton to assist in the surgical management of CFD.

Acrylic Cranioplasty for Cranial Defects Following Meningioma Surgery: A Case Series

Background: Meningiomas are the most prevalent primary intracranial tumors, which are treated with surgical resection. This procedure may result in cranial defects, leading to significant functional and aesthetic impairments. Lately, acrylic cranioplasty has emerged as a promising technique for repairing these defects. Objectives: The current retrospective review investigated patients, who underwent reconstructive cranioplasty following meningioma surgery between November 2021 and March 2023. Methods: Thirteen patients, who underwent cranioplasty surgery to repair extensive skull defects following meningioma surgery, were included as subjects. Eleven patients were female and all of them had a history of using progesterone contraception for 10 to 30 years. Two patients were male and had comorbid diabetes mellitus. Patients’ ages varied between 39 and 59 years old. The interval between craniectomy and cranioplasty was about 45 days. The material used for cranioplasty was polymethyl methacrylate prostheses. It started with a CT scan to determine the location and size of the skull defect. We reconstructed the defect, using computer-aided design and computer-aided manufacturing (CAD/CAM) to produce a prosthesis that was specific to each patient. This 3D-printed prosthesis was designed to manufacture a mold, which was sterilized and intraoperatively used. Results: We conducted post-operative surgery follow-up for up to 3 months. After 1 month of post-operative surgery follow-up, 2 out of our 13 patients developed cerebrospinal fluid leakage. Conclusions: Acrylic cranioplasty using CAD/CAM technology and 3D printing has shown potential for producing patient-specific implants to repair extensive skull defects. However, careful monitoring for post-operative complications is essential.

Fracture resistance and failure mode of three esthetic CAD-CAM post and core restorations

BackgroundThe rising demand for improved aesthetics has driven the utilization of recently introduced aesthetic materials for creating custom post and core restorations. However, information regarding the fracture resistance of these materials remains unclear, which limits their practical use as custom post and core restorations in clinical applications.Aim of the studyThis study aimed to evaluate the fracture resistance of three non-metallic esthetic post and core restorations and their modes of failure.Materials and methodsThirty-nine single-rooted human maxillary central incisors were endodontically treated. A standardized post space preparation of 9mm length was performed to all teeth to receive custom-made post and core restorations. The prepared teeth were randomly allocated to receive a post and core restoration made of one of the following materials (n=13): glass fiber-reinforced composite (FRC), polyetheretherketone (PEEK) and polymer-infiltrated ceramic-network (PICN). An intraoral scanner was used to scan all teeth including the post spaces. Computer-aided design and computer-aided manufacturing (CAD-CAM) was used to fabricate post and core restorations. Post and core restorations were cemented using self-adhesive resin cement. All specimens were subjected to fracture resistance testing using a universal testing machine. Failure mode analysis was assessed using a stereomicroscope and SEM. The data was statistically analyzed using One-Way ANOVA test followed by multiple pairwise comparisons using Bonferroni adjusted significance level.ResultsCustom PEEK post and core restorations displayed the least fracture load values at 286.16 ± 67.09 N. In contrast, FRC exhibited the highest average fracture load at 452.60 ± 105.90 N, closely followed by PICN at 426.76 ± 77.99 N. In terms of failure modes, 46.2% of specimens with PICN were deemed non-restorable, while for PEEK and FRC, these percentages were 58.8% and 61.5%, respectively.ConclusionsWithin the limitation of this study, both FRC and PICN demonstrated good performance regarding fracture resistance, surpassing that of PEEK.

A method of fabricating a stackable CAD-CAM custom record tray for complete dentures

Digital complete denture fabrication has advanced with the integration of computer-aided design and computer-aided manufacturing (CAD-CAM), intraoral scanning, and 3-dimensional printing. A method of fabricating a stackable CAD-CAM custom record tray for complete dentures is introduced. The method combines a custom tray, record base, and occlusion rim in a single piece.

3D printers and their use in prosthetic dentistry

In recent years, the use of computer-aided design and computer-aided manufacturing (CAD/CAM) has increased considerably in addition to the traditional methods used in routine. CAD/CAM technology has many advantages. However, despite these advantages, it has a very important disadvantage such as material waste. Today, the technology that overcomes this problem is the additive manufacturing method with three-dimensional printers. This method has recently replaced the traditional subtractive computer-aided design and manufacturing technology in prosthodontics. The use of 3D printers has been increasing in recent years due to its advantages such as ease of production, time saving and material saving, freedom of design, error-free and faster production. It is also predicted that the use of this technology will increase in the future and will be the main method for digital manufacturing. The aim of this review is to evaluate the production methods of 3D printers, the areas of use in prosthodontics, the advantages and disadvantages of 3D production methods, and to review the purposes of use, materials used and developments in prosthodontics.

Clinical outcomes of milled, 3D-printed, and conventional complete dentures in edentulous patients: A systematic review and meta-analysis.

This systematic review aims to compare clinical outcomes of digital dentures with conventional dentures. This study followed the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) guidelines and was registered in Prospero. The formulated population, intervention, comparison, outcome (PICO) question was "What is the clinical outcome of digital versus conventional complete dentures (CDs) in edentulous patients?". The search strategy used three main electronic databases and an additional manual search was completed in August 2023 by following an established search strategy. Initial inclusion was based on titles and abstracts, followed by a detailed review of selected studies, and clinical studies that evaluated the clinical outcome of digital (milled or 3D-printed) versus conventional CDs were included. A qualitative analysis for clinical studies was used to assess the risk of bias. The certainty of the evidence was assessed according to the grading of recommendations, assessment, development, and evaluations (GRADE) system. In addition, a single-arm meta-analysis was performed to evaluate the retention between digital versus conventional CDs. The initial search yielded a total of 947 articles, out of which 19 were selected for a comprehensive review, and six met the eligibility criteria to be included in this systematic review. The computer-aided design and computer-aided manufacturing (CAD-CAM) CDs showed increased retention, no relevant differences in oral health-related quality of life (OHRQoL), and shorter working time compared to conventional dentures. Two studies were eligible for meta-analysis; retention was significantly better among CAD-CAM fabricated dentures (standardized mean difference [SMD] 0.501) than conventional dentures. The heterogeneity between studies was high (95% CI: 0.049-0.952). Clinically, both the milled and the 3D-printed CD fared better than conventional dentures in terms of retention, reduction in the number of appointments, improved patient comfort, and improved predictable maintenance of the denture. Patients' perceptions and satisfaction were independent of the digital and conventional fabricated dentures.

Comparative evaluation and co-relation in variation of curve of Spee and curve of Wilson in Class II div. 1, Class II div. 2, and Class III as against Class I malocclusion in central India population- an in vitro study

Introduction Getting acceptable cosmetic results in the soft tissues of the face serves as the foundation for orthodontic treatment planning. Also, in order to achieve healthy static and dynamic occlusal interactions, the teeth must be positioned within the basal bone at the correct position, angle, and inclination. To avoid periodontal issues, provide stability, and achieve a functional occlusion, it is essential to ascertain the individual’s dental arch form before starting of treatment and thus to utilise the mechanics that follow throughout the treatment. Objectives To evaluate and compare variation in Curve of Spee and Curve of Wilson in Class II Div.-1, Class II-Div-2 and Class-III as against Class I malocclusion in central India population. Methodology Irreversible hydrocolloid impression will be taken with perforated metal stock trays and stone cast will be poured. This will be scanned using CAD CAM machine and curve of Spee and Wilson will be measured using reverse engineering. Expected Result It will assist us in treatment planning for preventing periodontal issues, assuring stability, and achieving functional occlusion by evaluating and comparing the Spee and Wilson curves in Class II Divison-1, Class II Divison-2, and Class-III malocclusion with Class-I malocclusion. Conclusion Every single patient receiving orthodontic treatment has the COS, which is crucial to achieving a stable occlusion. Almost every patient who receives orthodontic treatment eventually experiences the Spee Curve. Since there aren’t many studies examining the relationship between the Curves of Spee and Wilson, their impact on dentoskeletal morphology, and their role in occlusal stability.

Impact of various aging treatments on the microhardness and surface roughness of CAD-CAM monolithic restorative materials.

Dental ceramics deteriorate as a result of thermal aging and exposure to acidic solutions, which change their microhardness and surface roughness. This study assessed the resistance of several computer-aided design and computer-aided manufacturing (CAD-CAM) restorative dental materials in terms of surface roughness and microhardness following exposure to acidic solutions and thermal aging. Five different monolithic CAD-CAM restorative materials, two leucite-reinforced glass ceramics (G-Ceram and CEREC Blocs), a zirconia-infiltrated lithium silicate (Celtra Duo), a resin nanoceramic (Grandio), and monolithic zirconia (inCoris TZI), were used to create 2-mm-thick rectangular specimens (n = 100). After being immersed in either acidic saliva (pH = 4.0) (ST) or gastric juice (pH = 1.2) (GT), each material was subjected to 10,000 cycles of thermal aging. The Vickers microhardness and average surface roughness of the specimens were assessed at baseline, following thermal aging and exposure to either gastric juice or acidic saliva. The surface properties were examined using an atomic force microscope. The Mann‒Whitney U test with Bonferroni correction and the Wilcoxon signed-rank test was used for statistical analysis (a = 0.05). The surface roughness of two leucite-reinforced glass ceramics (G-ceram and CEREC) significantly decreased with ST (p = 0.027 and p = 0.044). Only the CEREC was affected when the aging protocols were compared, and the ST group had a significant reduction in roughness (p = 0.009). The microhardness values significantly decreased after both aging protocols in all groups except for the ST subgroup of G-Ceram. Only inCoris was affected when the aging protocols were compared, and the GT group exhibited a significant reduction in microhardness (p = 0.002). The surface roughness of the tested materials was not affected by the GT. Only leucite ceramics exhibited a decrease in surface roughness in the ST stage. Both aging processes produced a significant decrease in the microhardness of the tested ceramics. Leucite-reinforced glass-ceramic materials may be advantageous for patients with gastroesophageal reflux disease and those with a diet high in acidic foods due to their lower values for changes in microhardness and surface roughness compared to those of other CAD-CAM materials.

Comparison of the shear bond strengths of two different polyetheretherketone (PEEK) framework materials and CAD–CAM veneer materials

BackgroundThis study evaluated the shear bond strength (SBS) of two different polyetheretherketone (PEEK) and CAD-CAM materials after aging.MethodsA total of 42 frameworks were designed and milled from 2 different PEEK discs (Copra Peek, P and BioHPP, B). P and B frameworks were divided into 3 subgroups (n = 7). 14 slices were prepared each from feldspathic ceramic (Vitablocs Mark II, VM), hybrid nanoceramic (Cerasmart, CS), and polymer-infiltrated ceramic (Vita Enamic, VE) blocks. After surface preparations, the slices were cemented to P and B surfaces. The samples were subjected to thermal aging (5000 cycles). SBS of all the samples was measured. Fractured surfaces were examined by SEM/EDX analysis. The Shapiro–Wilk, Two-way Robust ANOVA and Bonferroni correction tests were used to analyze the data (a = .05).ResultsFrameworks, ceramics, and frameworks x ceramics had significant differences (p < 0.05). The highest SBS value was seen in B-VM (p < 0.05). VM offered the highest SBS with both P and B. The differences between P-VM, P-CS, P-VE and B-CS and B-VE were insignificant (p > 0.05). According to EDX analysis, ytterbium and fluorine was seen in B content, unlike P. While VM and CS contained fluorine, barium, and aluminum; sodium and aluminum were observed in the VE structure.ConclusionBonding of P and B with VM offers higher SBS. VM, CS and VE did not make any difference in SBS for P, however VM showed a significant difference for B.

Development of ZTA (80% Al2O3/20% ZrO2) pre-sintered blocks for milling in CAD/CAM systems

The present work aims to develop a production method of pre-sintered zirconia-toughened-alumina (ZTA) composite blocks for machining in a computer-aided design and computer-aided manufacturing (CAD-CAM) system. The ZTA composite comprised of 80% Al2O3 and 20% ZrO2 was synthesized, uniaxially and isostatically pressed to generate machinable CAD-CAM blocks. Fourteen green-body blocks were prepared and pre-sintered at 1000 °C. After cooling and holder gluing, a stereolithography (STL) file was designed and uploaded to manufacture disk-shaped specimens projected to comply with ISO 6872:2015. Seventy specimens were produced through machining of the blocks, samples were sintered at 1600 °C and two-sided polished. Half of the samples were subjected to accelerated autoclave hydrothermal aging (20h at 134 °C and 2.2 bar). Immediate and aged samples were characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD). Optical and mechanical properties were assessed by reflectance tests and by biaxial flexural strength test, Vickers indentation and fracture toughness, respectively. Samples produced by machining presented high density and smooth surfaces at SEM evaluation with few microstructural defects. XRD evaluation depicted characteristic peaks of alpha alumina and tetragonal zirconia and autoclave aging had no effect on the crystalline spectra of the composite. Optical and mechanical evaluations demonstrated a high masking ability for the composite and a characteristic strength of 464 MPa and Weibull modulus of 17, with no significant alterations after aging. The milled composite exhibited a hardness of 17.61 GPa and fracture toughness of 5.63 MPa m1/2, which remained unaltered after aging. The synthesis of ZTA blocks for CAD-CAM was successful and allowed for the milling of disk-shaped specimens using the grinding method of the CAD-CAM system. ZTA composite properties were unaffected by hydrothermal autoclave aging and present a promising alternative for the manufacture of infrastructures of fixed dental prostheses.

Biomechanics of Central Incisor Endocrowns with Different Lengths and Milled Materials after Static and Vertical Loading: A Finite Element Study.

The aim of this study was to compare and assess the stress distribution and failure possibility of endodontically treated central incisor protected with endocrowns with different heights, with various CAD-CAM blocks such as IPS e.max CAD, Katana Zirconia, and Zolid Fx Zirconia. A root canal-treated central incisor (plastic model) restored with an endocrown was scanned with a laser scanner to prepare a control model with a CAD software and then transferred to an FEA software. Proposed crown heights were 2, 4, and 6 mm. The model that was duplicated and restored with CAD-CAM blocks, IPS e.max CAD, Katana Zirconia, and Zolid Fx Zirconia were tested as endocrown materials. Bone geometry was simplified to be two coaxial cylinders in all models. Stress distributions under 50 N axial and oblique (with 135° angle from the vertical plane) loading were analyzed. Each model was then subjected to two occlusal loading conditions-the lingual slope of the incisal edge and the junction between incisal and middle thirds. Eighteen runs and calculations were performed to determine the endocrown height and material effect. The results showed a minor or negligible effect of changing the endocrown material. Increasing endocrown height was shown to reduce stresses and deformations on most of the model components (bone, gutta-percha, periodontal ligament, and endocrown), except root and cement. Differences in deformations and stresses between the two models of 4 and 6 mm were relatively smaller (ranged between 1% and 30%) compared to those between the 2 and 4 mm models (ranged between 10% and 400%). The material used to fabricate endocrowns did not show considerable effect on the underlying structures. However, the endocrown design (2, 4, and 6 mm height) was shown to affect all components of the studied systems. Increasing endocrown height is recommended for bone, periodontal ligaments, and endocrown body, as it reduces stresses and deformations. On the other hand, it dramatically increases stresses on the root and cement layer. Smaller endocrown sizes represent an acceptable treatment option when there is a healthy periodontal state, while using larger sizes will be more suitable when there is a periodontal compromise with bone loss.

Transitioning from injectable resin composite restorations to resin composite CAD/CAM veneers: A clinical report.

To describe a shift from injectable resin composite technique to composite resin computer-aided design and computer-aided manufacturing (CAD/CAM) veneers in addressing esthetic concerns associated with diastemas between anterior lower teeth in a clinical case. Among several techniques proposed for direct resin composite restoration, the "Injectable resin composite technique" has gained popularity for its time-efficiency, reduced technique sensitivity, and diminished reliance on clinician skills. However, challenges such as staining and the need for frequent polishing follow-ups may prompt the consideration of more stable alternatives such as indirect veneer restorations. While ceramic veneers offer superior mechanical and optical properties, resin ceramic veneers, especially those milled from CAD/CAM resin ceramic blocks, offer advantages such as rapid, cost-effective production, simplified intra-oral repairs, less susceptibility to fracture, superior stress absorption, and requires minimal tooth preparation, making them an appealing option for many patients. Moreover, a fully-digital approach not only streamlines the process but also saves time and labor while ensuring the delivery of high-quality restorations to patients. In addressing a patient's dissatisfaction with constant polishing of direct resin composite restorations, a shift to resin composite CAD/CAM veneers was implemented. Utilizing a fully-digital approach with CAD/CAM resin ceramic restorations successfully restored both esthetics and function. While the injectable resin composite technique achieves immediate esthetic results, its low color stability necessitates frequent polishing sessions. The replacement of direct resin composite restorations with CAD/CAM resin composite veneers becomes a viable option for patients seeking more stable restorations that require fewer follow-ups. This transition addresses both esthetic concerns and the need for enduring solutions in restorative dentistry.

Virtual Surgical Planning and Customized CAD/CAM Cranial Implants: Preoperative and Intraoperative Strategies for Temporal Intraosseous Meningioma Resection.

Primary intraosseous meningioma (PIM) is a rare subtype of extradural meningiomas, with the indication for surgical resection in most cases. With an increasing demand for efficient workflows with optimal functional and cosmetical results, techniques for bone reconstruction after resection are developing rapidly. The authors present 2 cases with one-stage cranioplasty after resection of PIM, using 3D technology for preplanned patient-specific implants. In the first case, a premanufactured patient-specific PEEK implant was used for reconstruction; in the second case, a 3-dimensional (3D)-based premanufactured silicon mold was used to produce a customized PMMA implant intraoperatively. Both techniques enabled the surgeons to achieve optimal intraoperative fit of the implant after craniectomy, leading to satisfying functional and cosmetic results. The use of 3D technology, such as Computer-Aided Design and Computer-Aided Manufacturing (CAD/CAM) for the production of patient-specific implants can optimize 1-stage cranioplasty after PIM resection.

Polymer-Infiltrated Ceramic Network Produced by Direct Ink Writing: The Effects of Manufacturing Design on Mechanical Properties

Polymer-infiltrated ceramic network (PICN) materials have gained considerable attention as tooth-restorative materials due to their mechanical compatibility with human teeth, especially with computer-aided design and computer-aided manufacturing (CAD/CAM) technologies. However, the designed geometry affects the mechanical properties of PICN materials. This study aims to study the relationship between manufacturing geometry and mechanical properties. In doing so, zirconia-based PICN materials with different geometries were fabricated using a direct ink-writing process, followed by copolymer infiltration. Comprehensive analyses of the microstructure and structural properties of zirconia scaffolds, as well as PICN materials, were performed. The mechanical properties were assessed through compression testing and digital image correlation analysis. The results revealed that the compression strength of PICN pieces was significantly higher than the respective zirconia scaffolds without polymer infiltration. In addition, two geometries (C-grid 0 and C-grid 45) have the highest mechanical performance.

The effect of immersion in water on deformation with the variety of denture base materials and manufacturing techniques.

To evaluate the effect of immersion in water on deformation of maxillary denture bases created by computer-aided design and computer-aided manufactured (CAD-CAM), and heat-polymerized resin fabrication techniques under loading condition. Two-millimeter thick denture bases were fabricated using four techniques: CAD-CAM milling (CCM) (Polywax; Yamahachi), 3D printing (3DP) (BV0005; NextDent), compression molding (CM) (Luciton 199), and injection molding (IM) (Ivobase) (n = 5 per group). Three static 49 N loads were applied perpendicular to each denture base, and the mean strain value (MSV) was recorded by strain gauges attached to the denture surface. The denture bases were stored at 37°C in distilled water for 14 and 28 days, and the MSVs under the same static load were recorded. The highest MSVs were observed at the posterior palatal seal, tuberosity, and labial notches of the dentures. The lowest MSVs were recorded for the CCM group, then the CM and IM. The highest MSVs were recorded for the 3DP group. No significant differences in regional MSVs (P > .05) were observed among the CCM, CM, and IM after 14 and 28 days in water. Large deviations in MSVs were recorded for the 3DP group across the measurement sites after water exposure (P < .05). CCM had the lowest denture deformation under static loading. After immersion in water, the deformation changes under static loading were stable for CCM, CM, and IM. However, variations among the materials used in 3DP group influenced the mechanical performance and presented larger deformations. Int J Prosthodont. 10.11607/ijp.8332.

Virtual Surgical Guidance Improves Quality of Life Following Scapular Free-Flap Reconstruction of Maxillary Defects

BackgroundThe best way for maxillary reconstruction remains the subject of debate, with negative impacts on the patient’s quality of life (QOL). PurposeThis study was designed to evaluate the QOL outcomes following maxillary reconstruction using a scapular-free flap, with and without the computer-aided design and computer-aided manufacturing (CAD/CAM) technique. Study design and patientsA prospective randomized controlled clinical trial was performed following the CONSORT checklist. To be included, patients suffering from maxillary defects without previous surgery or lymph node involvement were selected. Patients with poor oncological prognosis, deficient performance status, preoperative chemotherapy, or radiotherapy, besides vascular contraindications, were excluded. Predictor variableThe predictor variable was the reconstruction technique, grouped into two equal categories. Patients were randomly assigned to reconstruction with a scapular-free flap, with the control group not utilizing a guide and the study group utilizing a CAD/CAM-customized guide. Outcome variableThe primary outcome variable was the various domains of QOL, measured using the University of Washington-QOL (UW-QOL) score, 12 months after reconstruction. Covariatesage; sex; scapular flap side; and maxillary defect tumour type, histopathology, side, length, class, sagittal, and axial differential areas were considered. AnalysesShapiro-Wilk and Kolmogorov-Smirnov tests were performed for normality. For comparisons between the two groups, Student’s t-test and Mann-Whitney test were used. The category variables were compared using the chi-square test. p ≤ 0.05 was considered statistically significant. ResultsThe sample was composed of twenty-two eligible patients, eleven in each group. The mean age of the control group was (50.09±17.14) years, and 45.45% were male, while in the study group, the mean age was (48.36±14.14) years, with 36.36% male. All the patients were evaluated, showing statistically significant differences between control and study groups in terms of pain, appearance, chewing, swallowing, speech, and shoulder (p ≤ 0.05), indicating that the scapular-free flap with a CAD/CAM osteotomy guide had improved the patient's QOL. ConclusionsThe findings of this study indicate that VSP with a CAD/CAM customized osteotomy guide using a scapular-free flap can improve QOL in maxillary reconstruction in terms of pain, appearance, chewing and swallowing food, pronouncing words, and shoulder QOL outcomes.

Effect of a Novel ‘Scan Body’ on the In Vitro Scanning Accuracy of Full-Arch Implant Impressions

ObjectiveThis in vitro study aimed to determine whether a newly designed arcuate scan body can improve intraoral scanning accuracy for implant rehabilitation of edentulous jaws. Material and methodsA master model containing 4 implant abutment replicas was fabricated and digitized with different scan bodies using an intraoral scanner. Four types of scan bodies were evaluated: original scan bodies (group OS), computer-aided design and computer-aided manufacturing (CAD/CAM) scan bodies without extension (group CS), CAD/CAM scan bodies with straight extension (group CSS), and CAD/CAM scan bodies with arcuate extension (group CSA). Conventional splinted open-tray impressions (group CI) were used as controls. The master model and the poured casts were digitized using a laboratory scanner. Impressions were repeated 10 times each in 5 groups. Scans in standard tessellation language format were exported to reverse engineering software and root mean square (RMS) values were used for trueness and precision assessments. In each group, 45 RMS values were acquired for precision evaluation and 10 RMS values were obtained for trueness assessment. Statistical evaluation was performed with the Kruskal–Wallis test and Dunn–Bonferroni test (α = 0.05). ResultsThe median trueness values were 41.40, 55.95, 39.80, 39.75, and 22.30 μm for group OS, CS, CSS, CSA, and CI, respectively. CI showed better trueness than OS (P = .020), CS (P < .001), and CSS (P = .035). The median precisions for group OS, CS, CSS, CSA, and CI were 47.40, 51.50, 43.90, 25.20, and 24.60 μm. respectively. The precision of CSA and CI were higher than OS (P < .001), CS (P < .001), and CSS (P < .001). Between CI and CSA, there was no significant difference (P = 1.000). ConclusionsFor full-arch implant rehabilitation, the scan body with arcuate extension could improve the intraoral scanning precision and showed similar 3-dimensional discrepancy compared to conventional splinted open-tray impressions.

CAD-CAM fabrication of semiprecision LOCATOR-style abutments to correct severely misaligned implants supporting a 4-implant maxillary overdenture

Implant-supported removable overdentures are a popular treatment option with a favorable impact on a patient’s quality of life. A maxillary removable overdenture without palatal coverage should be supported by at least 4 implants uniformly distributed around the arch and connected by either semiprecision attachments or a bar. Optimally these 4 implants should be parallel or have their long axes nearly aligned to facilitate the prosthodontic phase of treatment by allowing the use of standard components. A computer-aided design and computer-aided manufacturing (CAD-CAM) procedure to produce LOCATOR-style attachments (T-L Custom abutments; TruAbutment Inc) to manage the restoration of 4 misaligned implants is described.

Clinical Evaluation of Two Distinct Materials for Implant-Supported Interim Fixed Partial Prostheses: An Original Research

ABSTRACT Aim: This study aimed to evaluate the clinical efficacy of posterior resin implant-supported fixed partial dentures (FPDs) made from two different computer-aided design and computer-aided manufacturing (CAD–CAM) materials: polymethylmethacrylate (PMMA) and polyoxymethylene (POM). Materials and Methods: Twenty-one patients received a total of 49 interim implant-supported FPDs. The same participant received PMMA and POM as part of the control and experimental groups, respectively. The restorations were evaluated 1 week, 3 months, and 6 months after placement. In addition, their functional wear and color stability were assessed. Nonparametric statistics (α = 0.05) were used to analyze the data. Results: The study found that PMMA outperformed POM in surface and color parameters, with more fractures occurring with internal conical connection implants. The color stability analysis showed ΔE*ab values of 7.18 for PMMA and 8.8 for POM, with no significant differences. After 6 months of operation, both materials showed a significant increase in wear, but no significant differences were found within the materials. Conclusion: The study found that PMMA interim implant-supported FPDs outperformed POM in surface and color parameters, while polymer posterior implant-supported FPDs with internal conical connection implants were more fracture-prone.

Comparison and Evaluation of Fracture Toughness of Milled, 3D-Printed, and Conventional Polymethyl Methacrylate: An In Vitro Study

ABSTRACT Introduction: Dentures aim to replicate natural dentition’s esthetics and functions as much as possible. With computer-aided design/computer-aided manufacturing (CAD/CAM) technology, dentistry had a new renaissance with workflow and materials. Aim: The aim is to compare the fracture toughness of the milled, 3D-printed, and conventional polymethyl methacrylate (PMMA) to those processed conventionally. Materials and Methods: 10 CAD MILLED PMMA BLOCKS, 10 3D PRINTED PMMA BLOCKS, and 10 CONVENTIONAL (HEAT CURE) PMMA BLOCKS. Results: A significant difference was seen in the mean flexural module when compared among three study groups as P &lt; 0.05. It was found to be maximum in CAD/CAM PMMA, followed by conventional heat cure and 3D-printed PMMA. Conclusion: Formlabs and Dentca (3D-printed) were significantly weaker in fracture toughness compared to Leucitone 199 (conventional) (P &lt; 0.05). Leucitone 199 (conventional) was significantly weaker in fracture toughness compared to Avadent (CAD CAM) (P &lt; 0.05).